|
|
Bulgarian 24mm - Designed for your AK-74 Rifle/Krinkov! US made Krinkov 4 Piece flash hiders are made of 4130 steel and the cone is nickel plated inside and out. The main body and cap are phosphated black.
Marked USA and counts as one part towards 922r
|
These M92 Barrel Extensions are made from 6061 aluminum and will bring your barrel to the legal length once permanently attatched. These are threaded to fit the M92/M85 26mm LH front sight/gas blocks. Otherwise they wouldn't be called M92 extensions.
|
These U.S.A. made Tapco G2 Double hook trigger groups are manufactured with 4140 tool grade carbon steel, have a mil spec dark black oxide finish. Precision secondary machining ensures perfect fit and function. They are heat treated to 45-48C Rockwell.
|
These U.S.A. made Tapco G2 Single hook semi-auto trigger groups are manufactured with 4140 tool grade carbon steel, have a mil spec dark black oxide finish. Precision secondary machining ensures perfect fit and function. They are heat treated to 45-48C
|
These jaws are machined from a bar of tool steel and hardened to my specifications. You will need the Harbor Freight 24" Bolt Cutters to use these jaws (the bolt cutters can be purchased for $11.99 normally and even less on sale). These jaws can easily ma
|
Yugo M92 26mm (Works with PAP pistols!)
US made Krinkov 4 Piece flash hiders are made of 4130 steel and the cone is nickel plated inside and out. The main body and cap are phosphated black.
Marked USA and counts as one part towards 922r compliance
|
These are made from heat treated 4130 steel and the rivets are a copy of an original AK center support rivet. The length is shorter than the 1mm center supports since the inside of the 1.5mm flats is smaller
|
3 inches of heat treated drill rod perfect for front sight & gas chamber installation.
|
3 inch length of heat treated drill rod perfect for installing AK rear sight blocks to barrel
|
AK-Builder Mil Spec Center Support and Rivet
|
TAPCO has taken the guess work out of selecting the right piston for your AK style rifle. The new universal gas piston works in standard AK-47s, AK-74's, Tantals, and even Saiga Rifles. This is all made possible by the use of a single bushing that allow
|
|
|
|
|
|
|
US AK-Builder Hungarian AMD 65 Gas Piston
|
|
Standard AK-47 barrel pins made from tool steel and heat treated like the originals. The dimensions of these were taken from Romanian barrel pins.
|
All US made Krinkov 4 Piece flash hiders are made of 4130 steel and the cone is nickel plated inside and out. The main body and cap are phosphated black.
The main body is engraved USA and counts as one part towards 922r compliance.
|
Slides over spring assembly with no disassembly required! Not the hard plastic buffers like the others.
|
Original Bulgarian Military Part *Used but good to excellent condition
|
original AK/AKM 47 barrel pins removed from demilled kits
|
These are not needed on the Yugo's unless you aren't using the original pistol grip mounting plate. This plate welds to the rear lower section of the receiver to strengthen that area when using folding stocks. As shown it is set-up for an underfolder. The
|
|
|
This plate welds to the rear lower section of the receiver to strengthen that area when using folding stocks. The bend is in the right spot and not touching the hole so there are not fitting issues.
This plate was used on the Russian and Bulgarian
s
|
This Poly-tech design retaining spring is made of military grade and specification wire. Retains hammer & trigger pin in AK “semi-auto” models and with its unique design, it is simple to install and remove. The top loop is retained by the rifle’s selec
|
|
|
Made in USA AK47 Slant Break. Marked "Made in USA." 1/14 LH Threades. Counts as one compliance part.
|
Safety Selector Plate-$9.99
|